Call Us: 08048077443

Send Email/SMS

Dry Running Seal - SPD103 & SPD103/B

Seal Type SPD103 and SPD103/B Mechanical Seals are designed for Top, Bottom and Side Entry Drives in Agitators, Mixers OR Blenders and where Non-Aggressive and Non-Hazardous Media are Sealed with the use of Cooling Liquid preventing against Dry Running. Construction of MOC designed of these Seals purpose of holding whole Rotary Parts together with the help of Snap Rings which eases while Installation and Removal of Seals.

  • Features:
    • These Seals are a Multiple Spring basically External Mounted Seal with 'O' Ring as Secondary Sealing Member.
    • Various Elastomer can be offer for various Liquid Applications.
    • These Seal Designed with Cooling Water Jacket which ensure cool Running of Seals.
    • Dry Run Seals are excellent with Low RPM
    • Operation in Vacuum conditions and as well as Undemanding Mixers Application
  • Materials
    • Seal Ring Faces : Carbon and SiC
    • Seat Faces : SiC and TC
    • Elastomer : Viton, TTV, FEP and FFKM
    • MOC : SS 316 - CHANGE OF MOC ON REQUEST
  • Operating Capabilities
    • Shaft Dia. : 20mm to 150mm
    • Pressure : Full Vacuum to 8 bar
    • Temperature : -30oC to 150oC
    • Speed : 300 r.p.m.

Dry Running Seal - SPD103 & SPD103/B

image not found

Dry Running Seal - SPD103 & SPD103/B

image not found


Dry Running Seal - SPD104 & SPD104/B

Seal Type SPD104 and SPD104/B Mechanical Seals are designed for Top, Bottom and Side Entry Drives in Agitators, Mixers OR Blenders in case when Non-Aggressive and Non-Hazardous Media are sealed with the use of Cooling Liquid Preventing against Dry Running. Construction of MOC designed of these Seals purpose of holding whole Rotary Parts together with the help of Snap Rings which make easy for Installation and Removal.

  • Features:
    • Balance Pusher Seals used for Sealing Environment.
    • Dry Run Seals are excellent in High Speed Seals for Operation in Vacuum Conditions as well as Undemanding Mixers applications.
    • In SPD104/J & SPD104/B/J Cool Set designed Mating Ring help to dissipate the Heat from Faces.
    • This Type Seal design may use either without Bearing OR with Integral Bearing.
    • These Seals are a Multiple Spring basically externally Mounted Seal with 'O' Ring as Secondary Sealing member. Various Elastomers can be offered for various media application
  • Materials
    • Seal Ring Faces : Spl. Carbon
    • Seat Faces : SiC
    • Elastomer : Viton, TTV, FEP and FFKM
    • MOC : SS 316 - CHANGE OF MOC ON REQUEST
  • Operating Capabilities
    • Shaft Dia. : 25mm to 150mm
    • Pressure : Full Vacuum to 8 bar
    • Temperature : -30oC to 140oC
    • Speed : 900 r.p.m.

Dry Running Seal - SPD104 & SPD104/B

Dry Running Seal - SPD104 & SPD104/B

Dry Running Seal - SPD104 & SPD104/B

Dry Running Seal - SPD104 & SPD104/B


Dry Running Seal - SPD105 & SPD105/B

Seal Type SPD105 and SPD105/B Mechanical Seals are designed for Top Entry Drives in Glass Lined Vessel. Compact Economical Cartridge Mechanical Seal for Glass Lined Vessel. These Seal specially designed for any mixed and pressurized liquid in Vessel with Top Entry Agitators where no leakage of Highly Acidic Process Gas OR Fluids to the Environment can be tolerated. Complete Pre-assembled Tested Unit ready for installation. These Seal are used for Exclusive Solid Seal Faces, Stationary Seats, thus Lowest Level of Seal face distortion when Expose to Compressive Load and Thermal Pressure.

  • Features:
    • Balance Pusher Seals which gives better performance in and for Sealing Environment.
    • Dry Run Seals are excellent with Low RPM Operation in Full Vacuum and Pressure.
    • These Seals Design for using either without Bearing (SPD105) OR with Integral Bearing (SPD105/B).
    • Various Elastomers can be offer for various Liquid applications.
    • These Seals Designed with Cooling Water Jacket which ensure Cool Running of seals.
  • Materials
    • Seal Ring Faces : Carbon and SiC
    • Seat Faces : SiC and Ceramic
    • Elastomer : Viton, TTV, FEP and FFKM
    • MOC : SS 316 - CHANGE OF MOC ON REQUEST
  • Operating Capabilities
    • Shaft Dia. : 25mm to 150mm
    • Pressure : Full Vacuum to 8 bar
    • Temperature : -30oC to 150oC (Depending upon Elastomer)
    • Speed : 250 r.p.m.

Dry Running Seal - SPD105 & SPD105/B

Dry Running Seal - SPD105 & SPD105/B

Dry Running Seal - SPD105 & SPD105/B

Dry Running Seal - SPD105 & SPD105/B